My "select surfaces" is not active. How does this work?
I have a thin plates STEP drawing. i can select nodes and elements but no surfaces.
If i select an element and then select surface he selects the whole object.
Die Suche ergab 17 Treffer
- Mi 7. Dez 2022, 11:12
- Forum: Preprocessing
- Thema: Picking a surface
- Antworten: 1
- Zugriffe: 682
- Mo 30. Jun 2014, 16:56
- Forum: Postprocessing
- Thema: Linear calculation results interpretation
- Antworten: 8
- Zugriffe: 39917
Re: Linear calculation results interpretation
You helped me out here. :-). I thought i distributed the load on the surface (as i'm used to in Algor). but now i understand that will put in several 500N loads on the end of the rod. The results are then quite correct using your standard material. The Von mises stress from Algor is 90,01Mpa. This i...
- Mo 30. Jun 2014, 13:11
- Forum: Postprocessing
- Thema: Linear calculation results interpretation
- Antworten: 8
- Zugriffe: 39917
Re: Linear calculation results interpretation
Tried to send the model once more including the results. I expected a stress on the elements of about 130Mpa, but the results lie somewhere around 2,6E+3 (2600). This is a bit high and i'm sure it has to do With the fact that i'm not quite sure on the way the program Works. :roll: . The stresses on ...
- Mo 30. Jun 2014, 12:56
- Forum: Postprocessing
- Thema: Linear calculation results interpretation
- Antworten: 8
- Zugriffe: 39917
Re: Linear calculation results interpretation
Hmmm, that is strange. The model was calculated by Z88 i'm sure i sent the correct model. Will check again.
- Mo 30. Jun 2014, 09:40
- Forum: Postprocessing
- Thema: Linear calculation results interpretation
- Antworten: 8
- Zugriffe: 39917
Re: Linear calculation results interpretation
I will take a look at the input data. Did send a zip file to you to check.
- Fr 27. Jun 2014, 11:18
- Forum: Postprocessing
- Thema: Linear calculation results interpretation
- Antworten: 8
- Zugriffe: 39917
Linear calculation results interpretation
Now i got some results form my analysis however i have some difficulties to interpret these. I made the same analysi in Algor to verifiy if the results are rougly the same. It is not possible for me to see any correlation between the results of ALgor and Z88 aurora. I have created a rod fixed in a p...
- Fr 27. Jun 2014, 09:47
- Forum: Preprocessing
- Thema: Error "no surface set allowed"
- Antworten: 4
- Zugriffe: 2624
Re: Error "no surface set allowed"
Will do, it looks ok now.
- Fr 27. Jun 2014, 09:08
- Forum: Preprocessing
- Thema: Error "no surface set allowed"
- Antworten: 4
- Zugriffe: 2624
Re: Error "no surface set allowed"
Ok, thank Your for Your prompt reply. I thought to put this on the Whole surface as to simulate that the plate i completely fixed on this surface (like welded). I wil try to use Your solution an create the nodes to be fixed.
- Fr 27. Jun 2014, 08:26
- Forum: Preprocessing
- Thema: Error "no surface set allowed"
- Antworten: 4
- Zugriffe: 2624
Error "no surface set allowed"
Trying to start With Z88Aurora. When i try to add the displacements on the body i receive the Message "no surface set allowed". Can someone help on why this is not possible. I have a simple steel plate that has a fixed surface in one and and 2 forces up and Down on the side. I selected the...
- Fr 13. Jun 2014, 06:17
- Forum: Preprocessing
- Thema: Error: NETGEN
- Antworten: 7
- Zugriffe: 3696
Re: Error: NETGEN
Thank you, the problem was caused by the model being 2 seperate bodies. The meshing worked fine after i changed the STL to 1 body. leason learned.
- Mi 11. Jun 2014, 10:52
- Forum: Preprocessing
- Thema: Error: NETGEN
- Antworten: 7
- Zugriffe: 3696
Re: Error: NETGEN
Done.
The STL file is included in the zip.
The STL file is included in the zip.
- Mi 11. Jun 2014, 07:57
- Forum: Preprocessing
- Thema: Error: NETGEN
- Antworten: 7
- Zugriffe: 3696
Re: Error: NETGEN
Thank you i sent the model to your E-mail. This is a Windows Z88, but the same error is reproduced in my Linux Version.
- Sa 7. Jun 2014, 16:20
- Forum: Preprocessing
- Thema: Error: NETGEN
- Antworten: 7
- Zugriffe: 3696
Error: NETGEN
Hello, I imported a STL file of a simple beam to see how this program works. This is working just fine, i see the model. However if i'm trying to put in the mesh (TETGEN or NETGEN) the error is the same. "Error: NETGEN, please look at Netgen.log" this log doesn't help me much but perhaps s...
- Mi 4. Jun 2014, 12:12
- Forum: Linux
- Thema: Red screen on starting Z88 Aurora
- Antworten: 24
- Zugriffe: 29793
Re: Red screen on starting Z88 Aurora
Thank you Z88 now Works from SUSE64, but not UBUNTU64 while i work on ubuntu .
I will see what happens.
I will see what happens.
- Mi 4. Jun 2014, 09:28
- Forum: Linux
- Thema: Red screen on starting Z88 Aurora
- Antworten: 24
- Zugriffe: 29793
Re: Red screen on starting Z88 Aurora
@ccad: I did change this LANG parameter earlier, but perhaps i do something wrong. Going to the Language support in Ubuntu i see that the "regional Formats" are English (UK). The screen on Z88 stays red however. I never worked With Z88 on ubuntu (but used Ansys on Windows), so i'm not sure...